1.Imported motion parts
2.High precision cutting efficiency
3.cutting head can be manual 60 degree cutting
4. Waterproof and Dustproof ,internal lubrication system
5. Laser cross line positioning system(optional)
Teenking CNC Machinery CO. Ltd is located in Foshan, Guangdong, China. Teenking is an ISO9001 factory with CE for the waterjet cutting machine. We are professional in making waterjet cutting machine over than 10 years
Easy control mode new: User simply press "Start", the machine will automatically complete the remaining work
3 axis linkage motion control: Available in 3D cutting(3 axis linkage control)
Free nesting software: Easy program pretreatment, such as lead in/lead out, cut sequence, compensate
High precision control: Control accuracy 0.001mm(μ M control).
Auto speed control: Auto speeding up and down to optimize cutting in detail of corner, to reduce the training
Dual-pressure system: Pierce in low pressure and cut in high-pressure, optimize cutting in breakable material.
Comprehensive protection: Inlet water and pneumatic intermit sensor\over-pressure sensor\teeny-pressure sensor\over-stroke sensor\over-heat sensor\over-load sensor\check-valve disable sensor\soft limit\hardware limited sonsor
Power-off protection: User can continue the program after power-on, accurate by reference sensor.
Ball-screw wear backlash compensation: After input number of compensate, save precision as original.
Auto abrasive feeder: To maximize saving in abrasive.
More than 9 years water-jet cutting experience from TEENKING, to cut various material with different cut technology, are all included into inner parameters of exclusive version of TKW-NC Studio software.
All covered by stainless steel.
| Work area ( X, Y ) | TK -Trump G series ( G = Gantry type ) | |||
| X = Gantry beam | Y = Baseframe | |||
| The max travel of X axis: | 3050 mm | |||
| The max travel of Y axis: | 6050 mm | |||
| The max travel of Z axis: | 200mm | |||
| The max travel of A axis: | N/A | |||
| The max travel of C axis: | N/A | |||
| Max range of process(available cut area): | 3000X6000x200mm | |||
| Motion speed on axis | Ball bearing running on ball screw, design for fast movement. | |||
| Max. Speed in X&Y axis: | 10m/min(600ipm) | |||
| Max. Speed in Z axis: | 2.5m/min(100ipm) in Z axis | |||
| Max. Speed in A axis: | N/A | |||
| Max. Speed in C axis: | N/A | |||
| Tolerance | X axis per 300 mm | ±0 .05 mm (.002"), | ||
| Y axis per 300 mm | ±0 .08 mm (±0.003") | |||
| Cut Tolerance in X,Y per 300 mm | ± 0.05mm(±0.002" per ft) | |||
| Re-position precision | ± 0.01mm (±0.0004") | |||
| Max cutting tolerancein whole machine range | ±0.10mm | |||
| The max speed of process | 10m/min (400 ipm) | |||
| Water-dust proof system | All stainless steel covered | |||
| All operative part are protected by water-dust proof device | ||||
| Auto-gentry balance | available in gentry-type machine, one-click to reset the balance of gentry(vertical of X and Y) | |||
| Grids under grates | For small parts collection after cut(Optional) | |||
| Sludge removal access | Preset pipe lines into bottom of water tank, suitable for sludge removal system(Optional) | |||
| Auto-Lubrication | Auto-lubricate feeding to ball screws, guides, and all operative articulations, to keep long life performance. | |||
| CNC garnet feeder | (Patent No. ZL200820205756.X) | Accurate Volume Control Garnet Feeder(controlled by CNC controller) To feed the garnet averagely and accurately. | ||
| Linear guide & Ball Screw | servo system: Panasonic or Yaskawa (if customer request) , from Japan | |||
| linear-guide: HIWIN brand , form TAIWAN | ||||
| ball-screw: TBI brand , from TAIWAN | ||||
| s traighten ing system | (Patent No. ZL200820205793.0) | Straighteningthe long ballscrew with pneumatic cylinder to support a fast and stable movement | ||
| Water Return Prevent | return water stop valve, to prevent garnet get wet and block in the nozzle. | |||
| Fast clamping tool | Smaller work sheet can be easy to fix by these tools providing with machine. | |||
| Wireless control | Remote control ± X, ±Y, ±Z and program start, stop, pause by wirelesskeyboard. | |||
| Wireless hand wheel | Remote control ± X, ±Y, ±Z and program start, stop, pause by wireless hand wheel(optional) | |||
| High pressure piping | Ø6.35x9 meters & Ø9.53x1.6 meters high-pressure tube from USA. | |||
| Cutting head | 1,Strong flame support in favor of smooth cut. 2,"FLOW" type high efficiency cutting head. 3, available +/-60 degree manually tilt. | |||
| Z-height control: | 1, clear coordinate as origin, setting raise up height and pierce height for cut. | Move cutting head to any position within the range of machine, clear the coordinate to zero as origin. cutting head will be raised up between parts, pierce in higher level in order to avoid the nozzle blocked by garnet. | ||
| 2,input thickness of material being cut. | Machine will understand and set the height of cutting automatically. | |||
| 3,By Auto-Height Sensor(optional)(Patent No. ZL201320255626.8) | Automatic tracking the height during whole processing by detector, detecting distance can be customized. | |||
| Laser cross line positioning system | (optional) | Help for fast positioning of nozzle, easily set origin for X and Y axis. | ||
