1. MESI-25/30 Lab Precise Single Screw Co-Extruder
1.1 Features
* Modern designed extruder body where all components are fully enclosed
* Special low profile extruder body which allows for a low position of the die, enabling a longer cooling way for the film bubble.
* Stainless steel hopper, mounted on a convenient safety 3-step turret valve with positions for in-feed, shut off and emptying of the hopper trough a discharge chute.
* Extruder body on four heavy-duty lockable casters.
* Full steel cover over the extruder barrel with air venting grid on top.
1.2 Main Technical Parameters
Variable speed motor: 4KW, NORD, 3 sets
Gearbox: Reduction ratio: I=16.66, NORD, 3 sets
Screw diameter: 25mm, 3 sets
Screw material: 38CrMoAIA
Screw speed: Infinite variable: 0-120rmp
Barrel material: 42CrMo, 3 sets
Barrel temp. Control: 3 zones,
Heating/cooling: 1.5KWx4=6KW,
One-piece cast aluminum heater: 3 sets
Screen changer: Manual plate screen changer, 2X1KW=2KW, 3 sets
2. FBSI-3-500 Three-layer Co-Extrusion Blown Film Die
2.1 Features
* The blown film die is designed in consultation with a Germany expert to ensure optimum efficiency and a very even distribution of the melt in each layer.
* The melt distribution and spiral channels could be analyzed using advanced specific software to ensure the whole die with the best flow properties.
* The die is made of tool steel and is coated with low friction nickel where the inner parts have a mirror-polished surface.
* Each die layer can be heated independently to achieve different temperature control. The layers are isolated each other to minimize the heat transition.
2.2 Main Technical Parameters
Die width: 500mm
Material: Tool steel
Temp. Measurement: 3 zones
3. FBSI-3-300 Lab Precise Co-Extrusion Blown Film Tower
3.1 Features
* The tower is made of high strength aluminum profile.
* The height of the tower can be electrically adjusted by the high strength screw.
* The double-column and the track system ensure a high degree of stability so that the Nip-roll and the die could constantly maintain parallel within the height adjustment range.
* There are two pneumatically operated film Nip-rolls. One is covered with wear resistant rubber and another has a polished chrome surface.
* The Nip-rolls are driven by servo motor with stepless speed control.
* The bubble cage is equipped with a row of Teflon coated rollers. The rollers also could be made of carbon fiber reinforced thermosetting resin.
* The A-frame (collapsing gate) is equipped with carbon fiber rollers to ensure the best flattening effect with the minimum contact friction.
* There are 4 guide rolls on the down side.
3.2 Technical Parameters
Height of tower: 3200-4200mm
Max. Film web width: 500mm
Film thickness: 0.03-0.3mm
Blower of air ring: 2HP
Haul-off roll: Diameter: 80mm, width: 600mm
Haul-off speed: 0-10m/min, stepless speed
Winding roll: Diameter: 60mm, width: 600mm
Blowing air pressure: 0-6bar
Machine frame: European standard aluminum alloy profile with self-lock casters and leveling pads.
4. Controlling and Testing System
The independent control panel integrates all die control and all speed control of the extruders.
Siemens PLC controlling system
10.4"TFT touching screen
Speed control: Extruder, melt pump, casting roll, haul-off roll servo speed controller
DYNISCO melt temp. And pressure measurement: Melt pressure: 0-50Mpa; Melt temp.: 0-400° C
SCHNEIDER low voltage electric components: CE certificate
5. Optional Items
* Closed Loop Extruder Control
* Gear Pumps for Precise Controls of Layer Thickness
1.1 Features
* Modern designed extruder body where all components are fully enclosed
* Special low profile extruder body which allows for a low position of the die, enabling a longer cooling way for the film bubble.
* Stainless steel hopper, mounted on a convenient safety 3-step turret valve with positions for in-feed, shut off and emptying of the hopper trough a discharge chute.
* Extruder body on four heavy-duty lockable casters.
* Full steel cover over the extruder barrel with air venting grid on top.
1.2 Main Technical Parameters
Variable speed motor: 4KW, NORD, 3 sets
Gearbox: Reduction ratio: I=16.66, NORD, 3 sets
Screw diameter: 25mm, 3 sets
Screw material: 38CrMoAIA
Screw speed: Infinite variable: 0-120rmp
Barrel material: 42CrMo, 3 sets
Barrel temp. Control: 3 zones,
Heating/cooling: 1.5KWx4=6KW,
One-piece cast aluminum heater: 3 sets
Screen changer: Manual plate screen changer, 2X1KW=2KW, 3 sets
2. FBSI-3-500 Three-layer Co-Extrusion Blown Film Die
2.1 Features
* The blown film die is designed in consultation with a Germany expert to ensure optimum efficiency and a very even distribution of the melt in each layer.
* The melt distribution and spiral channels could be analyzed using advanced specific software to ensure the whole die with the best flow properties.
* The die is made of tool steel and is coated with low friction nickel where the inner parts have a mirror-polished surface.
* Each die layer can be heated independently to achieve different temperature control. The layers are isolated each other to minimize the heat transition.
2.2 Main Technical Parameters
Die width: 500mm
Material: Tool steel
Temp. Measurement: 3 zones
3. FBSI-3-300 Lab Precise Co-Extrusion Blown Film Tower
3.1 Features
* The tower is made of high strength aluminum profile.
* The height of the tower can be electrically adjusted by the high strength screw.
* The double-column and the track system ensure a high degree of stability so that the Nip-roll and the die could constantly maintain parallel within the height adjustment range.
* There are two pneumatically operated film Nip-rolls. One is covered with wear resistant rubber and another has a polished chrome surface.
* The Nip-rolls are driven by servo motor with stepless speed control.
* The bubble cage is equipped with a row of Teflon coated rollers. The rollers also could be made of carbon fiber reinforced thermosetting resin.
* The A-frame (collapsing gate) is equipped with carbon fiber rollers to ensure the best flattening effect with the minimum contact friction.
* There are 4 guide rolls on the down side.
3.2 Technical Parameters
Height of tower: 3200-4200mm
Max. Film web width: 500mm
Film thickness: 0.03-0.3mm
Blower of air ring: 2HP
Haul-off roll: Diameter: 80mm, width: 600mm
Haul-off speed: 0-10m/min, stepless speed
Winding roll: Diameter: 60mm, width: 600mm
Blowing air pressure: 0-6bar
Machine frame: European standard aluminum alloy profile with self-lock casters and leveling pads.
4. Controlling and Testing System
The independent control panel integrates all die control and all speed control of the extruders.
Siemens PLC controlling system
10.4"TFT touching screen
Speed control: Extruder, melt pump, casting roll, haul-off roll servo speed controller
DYNISCO melt temp. And pressure measurement: Melt pressure: 0-50Mpa; Melt temp.: 0-400° C
SCHNEIDER low voltage electric components: CE certificate
5. Optional Items
* Closed Loop Extruder Control
* Gear Pumps for Precise Controls of Layer Thickness
