Long Lifetime Co2 Laser Tubes adopt new technique of production and inflation formula for co2 gas, to ensure the high quality and stability of glass laser tubes. The lifetime of laser tube is up to 8000 hours, laser power is from 80 watts to 180 watts, it is very popular in thickness materials cutting.
1. Working Performance:
Cutting function.
Engraving function: Auxiliary engraving, when the working current is 4mA and the tube is in the state of preionization, the laser can be used for high-frequency impulse engraving.
2. Important Notice:
For this type CO2 Laser Tubes, do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror:
1) When the mirror is polluted, do not turn on the laser.
2) Blow the mirror surface sideway with air blower.
3) Spray the pure alcohol on the mirror surface with sprayer.
4) Turn on the laser after the alcohol gets fully volatilized.
5) If the methods above don't work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean the mirror surface from middle to edge. The best solution is to prevent the window from being polluted.
Attention: longlife Laser Tube is forbidden to clean the mirror with acetone.
The screw in the front and back ends of the laser tube is not allowed to be moved, otherwise the out power will be declined and even the tube may be scrapped.
Put the acryl 300mm far away from output mirror, when testing the laser spot.
3. Safety:
The laser beam is invisible light. Please wear protective glasses when debugging the laser. The positive pole is in high voltage. Pay attention to the security marks.
4. Storage and Transportation Requirement:
Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag. The storage environment is 2-40C, and the requested humidity is 10-60%. Pack the laser as in the original way.
Important notes: it is requested to cement the sponge together with laser tube to prevent the tube vertically sliding during transportation. The sponge in the side of output mirror must be 70mm beyond it, and the sponge in the side of reflecting mirror must be 50mm wider.
5. Tubes operated in wrong way will not be guaranteed by Manufacturer.
6.Specification:
1. Working Performance:
Cutting function.
Engraving function: Auxiliary engraving, when the working current is 4mA and the tube is in the state of preionization, the laser can be used for high-frequency impulse engraving.
2. Important Notice:
For this type CO2 Laser Tubes, do not clean the exterior surface of the output widow mirror with tools such as tampon; otherwise the output power will be seriously affected. The followings are the designated methods to clean up pollution in the exterior surface of window mirror:
1) When the mirror is polluted, do not turn on the laser.
2) Blow the mirror surface sideway with air blower.
3) Spray the pure alcohol on the mirror surface with sprayer.
4) Turn on the laser after the alcohol gets fully volatilized.
5) If the methods above don't work effectively, it is necessary to ask for the professional to use tampon with alcohol to clean the mirror surface from middle to edge. The best solution is to prevent the window from being polluted.
Attention: longlife Laser Tube is forbidden to clean the mirror with acetone.
The screw in the front and back ends of the laser tube is not allowed to be moved, otherwise the out power will be declined and even the tube may be scrapped.
Put the acryl 300mm far away from output mirror, when testing the laser spot.
3. Safety:
The laser beam is invisible light. Please wear protective glasses when debugging the laser. The positive pole is in high voltage. Pay attention to the security marks.
4. Storage and Transportation Requirement:
Pour out cooling fluid in the event of storage and transportation, and cover the output terminal with a dust-proof plastic bag. The storage environment is 2-40C, and the requested humidity is 10-60%. Pack the laser as in the original way.
Important notes: it is requested to cement the sponge together with laser tube to prevent the tube vertically sliding during transportation. The sponge in the side of output mirror must be 70mm beyond it, and the sponge in the side of reflecting mirror must be 50mm wider.
5. Tubes operated in wrong way will not be guaranteed by Manufacturer.
6.Specification:
|
Rated Power (watts) |
80 |
100 |
130 |
150 |
|
Max. Power (watts) |
90 |
120 |
150 |
180 |
|
Full Length (mm) |
1200 |
1400 |
1650 |
1850 |
|
Diameter (mm) |
80 |
80 |
80 |
90 |
|
Catalyze |
Yes |
Yes |
Yes |
Yes |
|
Triggering Voltage (KV) |
20 |
24 |
28 |
30 |
|
Operating Current (mA) |
27 |
28 |
29 |
30 |
|
Span Life (hours) |
8,000 |
8,000 |
8,000 |
8,000 |
|
Warranty Period (months) |
6 |
6 |
6 |
6 |
