Equipment Introduction
1.1 Equipment requirements: The device can process all kinds of spunlace non-woven,hot air fabric, hot-rolled fabric; acupuncture cloth, spunbond fabric, SMS,paper-plastic and other raw material.
It adopts heat embossing device, also it can add spraying hot melt adhesion according to customer request.
The spraying hot melt adhesion is that the machine extra to install the spraying device, it adhesive the hot melt plastic.
1.2 Equipment working principle: Longitudinal foldingcutting length automaticallyTransverse foldingoutput automaticallyProduct stacking,the whole line complete automatically.
1.3 Width of raw material: 2000mm
1.4 Folded width longitudinally arbitrary adjustable, the product Cutting length can be adjusted between 300-2500mm, length error of ± 1 mm.
1.5 Transverse folding: one half ,one- third,one -quarter,one sixth,one-eighth
1.6 The machine adopts the cylinder to promote the material and tension control automatically, without manual operation
1.7 All the drives use the imported servo motor, high precision
1.8 Touch screen control, only need to enter the data can change the specs,easy to operate.
1.9 Electronic-control is touch screen man-machine interface operation,built-in production time,counting,a preset number of automatic shutdown,etc.
1.10 Entire delivery system, strong, durable, non-polluting;
1.11 Electrical wiring specifications and reasonable,elegant,easy to operate.
Technical parameters:
2.1 Supply Voltage: 380V50HZ
2.2 Power: 5KW
2.3.Weight: 5 T
2.4.Speed: 0-40 m / min
2.5.Dimensions: 9900 * 2400 * 2150mm
2.6.machine color:silvery white
Famous Brand Equipment configuration list:
3.1 Servo drive: Delta (Taiwan) 5sets
3.2 Gear motors: Yongkun (Taiwan) 1set
3.3 PLC: Delta (Taiwan) 1set
3.4 Motion Controller: Delta (Taiwan) 1 set
3.5 Touch screen: Delta (Taiwan) 1set
3.6 Sensor: Omron (Japan) 3sets
3.7 Inverter: Delta (Taiwan) 1set
3.8 Low-voltage electrical: delixi 1set
3.9 Air shaft: 1set
3.10 Cylinder: airtac 1set
Machine structure Description
The host by the channel steel welded together,solid and firm,surface painting, The feeding part is aluminum alloy rack, the appearance is beautiful and will not get rusted permanently.
Electronic control system
5.1 PLC control system, touch screen man-machine interface operation,easy to operate, humanized design
5.2 Through the man-machine interface to adjust speed, the size of the finished product,and Stacking quantity.
5.3With Chinese and English operator interface,easy to operate
Installation,and terms of Service
6.1 we provide door to door service for domestic customers, foreign customers need to install the machine by themselves. Our engineer at the request of foreign customers can door-to-door service, but users are responsible for accommodation, round tickets visa fees and so on (domestic except). And pay our engineer 150USD one day.
6.2 The seller is responsible for equipment packaging costs, use FOB export situation
6.3 Random with common wearing parts and special tools
6.4 After leaving Shanghai port the buyer is responsible for the freight, insurance premiums and unloading
Considerations
8.1 The machine main components should be checked regularly, Such as welding and cutting bearing working case, filling oil appropriately to ensure that it is working properly.
8.2 Periodically check the wear of the welding, Appropriate adjust the pressure, In the case of guarantee welding well,make the pressure minimum.
8.3 Each unwinding trays tension should be checked in order to adapt to the production needs.
8.4the cutter pressure should be appropriated,otherwise easily lead to a situation such as knife fight
free parts
9.1 wrench : 1 piece
9.2 cutter : 2 pieces
touching screen
product sample
1.1 Equipment requirements: The device can process all kinds of spunlace non-woven,hot air fabric, hot-rolled fabric; acupuncture cloth, spunbond fabric, SMS,paper-plastic and other raw material.
It adopts heat embossing device, also it can add spraying hot melt adhesion according to customer request.
The spraying hot melt adhesion is that the machine extra to install the spraying device, it adhesive the hot melt plastic.
1.2 Equipment working principle: Longitudinal foldingcutting length automaticallyTransverse foldingoutput automaticallyProduct stacking,the whole line complete automatically.
1.3 Width of raw material: 2000mm
1.4 Folded width longitudinally arbitrary adjustable, the product Cutting length can be adjusted between 300-2500mm, length error of ± 1 mm.
1.5 Transverse folding: one half ,one- third,one -quarter,one sixth,one-eighth
1.6 The machine adopts the cylinder to promote the material and tension control automatically, without manual operation
1.7 All the drives use the imported servo motor, high precision
1.8 Touch screen control, only need to enter the data can change the specs,easy to operate.
1.9 Electronic-control is touch screen man-machine interface operation,built-in production time,counting,a preset number of automatic shutdown,etc.
1.10 Entire delivery system, strong, durable, non-polluting;
1.11 Electrical wiring specifications and reasonable,elegant,easy to operate.
Technical parameters:
2.1 Supply Voltage: 380V50HZ
2.2 Power: 5KW
2.3.Weight: 5 T
2.4.Speed: 0-40 m / min
2.5.Dimensions: 9900 * 2400 * 2150mm
2.6.machine color:silvery white
Famous Brand Equipment configuration list:
3.1 Servo drive: Delta (Taiwan) 5sets
3.2 Gear motors: Yongkun (Taiwan) 1set
3.3 PLC: Delta (Taiwan) 1set
3.4 Motion Controller: Delta (Taiwan) 1 set
3.5 Touch screen: Delta (Taiwan) 1set
3.6 Sensor: Omron (Japan) 3sets
3.7 Inverter: Delta (Taiwan) 1set
3.8 Low-voltage electrical: delixi 1set
3.9 Air shaft: 1set
3.10 Cylinder: airtac 1set
Machine structure Description
The host by the channel steel welded together,solid and firm,surface painting, The feeding part is aluminum alloy rack, the appearance is beautiful and will not get rusted permanently.
Electronic control system
5.1 PLC control system, touch screen man-machine interface operation,easy to operate, humanized design
5.2 Through the man-machine interface to adjust speed, the size of the finished product,and Stacking quantity.
5.3With Chinese and English operator interface,easy to operate
Installation,and terms of Service
6.1 we provide door to door service for domestic customers, foreign customers need to install the machine by themselves. Our engineer at the request of foreign customers can door-to-door service, but users are responsible for accommodation, round tickets visa fees and so on (domestic except). And pay our engineer 150USD one day.
6.2 The seller is responsible for equipment packaging costs, use FOB export situation
6.3 Random with common wearing parts and special tools
6.4 After leaving Shanghai port the buyer is responsible for the freight, insurance premiums and unloading
Considerations
8.1 The machine main components should be checked regularly, Such as welding and cutting bearing working case, filling oil appropriately to ensure that it is working properly.
8.2 Periodically check the wear of the welding, Appropriate adjust the pressure, In the case of guarantee welding well,make the pressure minimum.
8.3 Each unwinding trays tension should be checked in order to adapt to the production needs.
8.4the cutter pressure should be appropriated,otherwise easily lead to a situation such as knife fight
free parts
9.1 wrench : 1 piece
9.2 cutter : 2 pieces
touching screen
product sample
